background image

Safety Information 

OceanStor CloudStor CSE V100R001C01 

Quick Installation Guide 

 
 
 

 Issue: 

03 

 Date: 

2012-10-17 

 

 

Do not operate devices or handle cables on a stormy day. 

To avoid personal injuries, take off your electrostatic discharge (ESD) wrist strap before inserting a power cable.  

To avoid personal injuries, arrange enough persons to carry the devices according to the suggestion on the package. 

Before handling devices, wear an ESD suite, ESD gloves, or an ESD wrist strap and take off conductive objects such 

as ornaments and watches. 

 
 

 

 
 
 

To avoid device damage, ensure that the devices are grounded before powering them on. 

Do not insert or remove disks or cables during power-on of the CSE. When data is being read or written on hard 

disks, do not power off the device by cutting off power or holding down the power button for seconds. Otherwise, the 
hard disks may have bad tracks and data may be damaged. To power off the device, stop reading and writing data on 
the hard disks first and then send a shutdown command through the operating system (OS). 

 

Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.

Installation Process 

The power distribution system (DC or AC power distribution box), auxiliary tools (guide rails and floating nuts) are 
pre-installed  and cables (including power cables and network cables) are laid out in the system cabinet of the CSE 
before delivery.

 

确定

T3200 G3

在机柜中的位置

   Prepare the materials and 

installation tools. 

Take antistatic measures.

Install hardware devices of 

the CSE.

Connect cables.

Power on the devices and 

check indicator status.

Install software.

Start

End

Page 2

Page 14

Page 12 to 13

Page 7 to 11

Page 4 to 7

Page 3

Determine positions of 
devices in the cabinet.

Remove filler panels.

Install back-end storage 

devices.

Install a KVM.

Install a switch.

Install a SD-Node.

Page 4

Page 5

Page 5

Page 5

Page 5

Page 6

Install a C-Node.

Install a SMS modem.

Page 6

Page 6

Connect the SD-Node.

Connect the C-Node.

Connect the switch.

Connect the KVM.

Connect the SMS modem.

Connect the remote modem.

Page 10

Page 10

Page 11

Page 11

Page 11

Page 11

Install a Remote modem.

Page 7

Summary of Contents for V100R001C01















Reviews: