Huawei V100R021C00 User Manual Download

Page: 220 / 508

Figure 4-167 Installing positioning pins of a magnet

2. Insert the assembled magnet into the positioning holes in the door, and

secure the magnet to the door using the screws and rubber pad delivered

with the electronic lock, as shown in

Figure 4-168

NO TE

When securing the magnet to the door panel, do not over-tighten the screws so that the

rubber pad is elastic. The rubber pad will adjust the magnet to a correct position because of

its elasticity.

Figure 4-168 Installing a magnet

(1) Rubber pad

Step 8 (Optional) Adjust the magnet.

1. If the magnet cannot attract the door properly after power-on, place a

magnetized metal part near the magnet to check whether the magnet

provides a proper magnetic force.

2. If the magnetic lock and the magnet do not work properly, check and

troubleshoot the circuit.

----End

4.2.9.14 (Optional) Installing an In-Room Fingerprint and Card Reader with

a Keypad

Context

●

The BOM number of a fingerprint and card reader with a keypad is 02070174.

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

208

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands