Huawei V100R021C00 User Manual Download

Page: 309 / 508

Step 2 Commission cameras and set parameters for them. For details, see the delivered

documents.
1. Preview the site situation in real time and check the camera coverage through

videos. Adjust the lens if necessary.

2. On the View tab page, click the Network/Time tab to access the Network/

Time tab page.

Figure 5-26 Setting the IP address

Table 5-21 IP address parameters

Parameter

Description

IPv4 address

assignment

Method for obtaining the IP address. The options are

Obtain IP address automatically and Use the

following IP address. The default value is Obtain IP

address automatically.

IPv4 address

Camera IP address. This parameter is available only

when IPv4 address assignment is set to Use the

following IP address.
Enter the planned IP address, for example,

192.168.1.161. IP addresses starting with 127 are

invalid. You must enter an IP address starting with a

value that ranges from 1 to 223.

IPv4 gateway

Gateway IP address of the network where the camera is

located. The default value is 192.168.0.1.

IPv4 subnet

mask

Subnet mask of the network where the camera is

located. The default value is 255.255.255.0.

Primary DNS

Primary DNS IP address. The default value is 0.0.0.0.

Secondary DNS

Secondary DNS IP address. The default value is 0.0.0.0.

FusionModule800 Smart Small Data Center

User Manual

5 Power-On Commissioning

Issue 01 (2021-02-05)

297

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands