Huawei V100R021C00 User Manual Download

Page: 327 / 508

Figure 5-46 Initializing disks

Step 4 Choose whether to create a RAID group. To set disks as a RAID group, select

RAID1. To set disks to work independently, select NON-RAID.

NO TE

The VCN510 supports only RAID1 or NON-RAID. If only one disk is configured, the VCN510

supports only NON-RAID. This section assumes that two disks are configured for the

VCN510.

Table 5-27 Disk modes

RAID Mode

Description

RAID1

Two disks are required in RAID 1 mode. If RAID 1 is used,

disks back up each other. After recording data is stored in a

disk, the data will be simultaneously backed up to another

disk, ensuring high data storage reliability. However, the

disk usage of RAID 1 is lower than that of disks that work

independently.

NON-RAID

If disks work independently, recording data is stored into

two disks in sequence, ensuring high disk usage. However,

the data storage reliability of disks that work independently

is lower than that of RAID 1.

Step 5 Click Start. A risk warning is displayed.
Step 6 Click OK. The system starts to initialize the disks.

NO TE

The server will be restarted during the initialization of disks. The process takes about 5 to

10 minutes.

----End

Verification

Step 1 Choose Local Configuration > Local Disk.
Step 2 View the RAID group status in the RAID Groups area.

If RAID1 is selected for the disks, RAID 1 is created for both the system partition

(used to store system data) and data partition (used to store recordings).

FusionModule800 Smart Small Data Center

User Manual

5 Power-On Commissioning

Issue 01 (2021-02-05)

315

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands