Huawei V100R021C00 User Manual Download

Page: 340 / 508

Figure 5-64 Logging in to the iClient

4. Select Micro Edge Access.
5. Add an IVS1800.

Figure 5-65 Adding a device

NO TE

– If the iClient and IVS1800 are deployed in the same LAN, set Address to the

internal IP address of the IVS1800. If the iClient is installed on an external network

and the IVS1800 is deployed in the LAN, set Address to the external IP address of

the IVS1800.

– When the IVS1800 is added to the iClient by the admin user, the iClient checks

whether the login password of the admin user has been set. If the password is not

set, log in to the OMU portal to set the password.

6. Click Finish to go to the iClient.

Step 2 Add a camera. For details, see the documentation delivered with the device or

obtain the documentation by referring to the "Reference Documentation" section.

View the corresponding section.

FusionModule800 Smart Small Data Center

User Manual

5 Power-On Commissioning

Issue 01 (2021-02-05)

328

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands