Huawei V100R021C00 User Manual Download | Manualshive

Page: 352 / 508

background image

Prerequisites

Valid user name and password are available.

Procedure

Step 1 In the browser address bar, enter https://IP address of the NetEco server:31943,

and then press Enter.

NO TE

● 192.168.8.11 is the default IP address of the NetEco.
● Firefox ESR 52, Chrome 57 or later is supported.
● You are advised to set the display resolution as 1920*1080 or higher.
● Make sure that the IP address of the NetEco server is not contained in the compatibility view

website.

Step 2 Enter the User Name, Password, and click Login.

NO TE

● The preset user of NetEco is admin, the preset password is Changeme_123. This user has

all the operation rights on the managed objects. After the first login, change the

password in time to ensure account security and prevent unauthorized network attacks,

such as data tampering. Huawei will not be liable for any security issues caused by your

failure to change the preset password in time or password loss after changing.

● If the number of online users reaches the maximum number supported by the system, a

message is displayed, indicating that you cannot log in. In this case, contact the system

administrator.

● After you enter the incorrect password for three consecutive times, you must enter the

verification code upon the fourth login. After you enter the incorrect password for five

consecutive times, the user account or the IP address is locked for 10 minutes.

----End

5.3.13.1.6 Loading a NetEco License

The NetEco license file is used to control the functions and management

capabilities of the NetEco. Before using NetEco, you need to load a commercial

license.

Prerequisites

●

You have obtained a license.

●

You have logged in to the NetEco client using a web browser.

Procedure

Step 1 Click Import License file when you log in to the NetEco at the first time.

Step 2 Click

next to the License text box and select a license file.

Step 3 Click Upload.

The information about the imported license file is displayed.

FusionModule800 Smart Small Data Center

User Manual

5 Power-On Commissioning

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

340

«
...
350
351
352
353
354
...
»

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for V100R021C00

Brand: iGen Pages: 15

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 4

Brand: MadgeTech Pages: 4

Brand: MadgeTech Pages: 2

Brand: Magnum Pages: 10

Brand: Ebro Pages: 18

Brand: Ikusu Pages: 2

Brand: National Instruments Pages: 20

Brand: Madge Networks Pages: 16

Brand: YOKOGAWA Pages: 134

ULTRASONIC Portable

Brand: Calypso Instruments Pages: 13

DataLogger 4 Series

Brand: Magnetek Pages: 28

HiTemp140 Series

Brand: MadgeTech Pages: 4

HiTemp140X2 Series

Brand: MadgeTech Pages: 12

Brand: EasyLog Pages: 2

Brand: Tzone Pages: 16

Brand: Steren Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands