Huawei V100R021C00 User Manual Download

Page: 378 / 508

Maintenance Item

Operation

Expected Result

Troubleshooting

Check that the electric

heater contactor

works properly.
1. When the smart

cooling product is

on, set Diagnostic

Mode to Enter on

the Controls page,

and click Submit.

2. Choose Running

Parameters >

Diagnostic Mode

Parameters, set

Elec heater

manual control to

ON, and click

Submit. You can

hear a click sound

from the contactor.

Replace the electric

heating contactor if it

is faulty.

Cable

Check that no cable is

aged.

Replace aged cables.

Outdoor unit

Check that the

outdoor unit is secured

to the floor.

Tighten the screws

that secure the rack to

the floor.

Check that the fan

runs properly without

abnormal noise or

vibration, and the

blades rotate properly.

Replace the outdoor

unit by following

instructions in

6.4.3.2.1 Replacing

an Outdoor Fan

Check that the fan air

intake and exhaust

vents are not blocked.

Clear obstacles.

6.2 Troubleshooting

6.2.1 Power Supply and Distribution System Troubleshooting

Except mains outage, power supply and distribution faults are caused by the

damage or failure of one or more components. Rectify the faults based on fault

location and fault type.

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

366

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands