Huawei V100R021C00 User Manual Download

Page: 380 / 508

Symptom

Possible Cause

Measure

The indicators are off.

● Cables are loose.
● The fuse holder trips.
● The fuse is damaged.
● The indicators are

damaged.

● Connect the cables

again.

● Turn on the fuse

holder.

● Replace the fuse of

the indicators. For

details, see

6.4.2.2

Replacing a Fuse

● Replace the

indicators. For details,

see

6.4.2.3 Replacing

an Indicator

The general switch is

ON, the LCD displays no

information, and the

system does not perform

self-check.

The input power supply

is not connected.

Check the UPS input

power cable connection.

The input voltage is less

than the lower threshold

or greater than the

upper threshold.

Use a voltmeter to check

whether the UPS input

voltage meets

requirements.

The mains is normal, but

the AC input indicator is

off. The UPS works in

battery mode.

The UPS mains switch is

OFF.

Turn on the UPS mains

switch.

The input cable is not

properly connected.

Check the UPS input

power cable connection.

The UPS fails to

communicate.

● The UPS

communications cable

is not properly

connected.

● The UPS parallel cable

is not properly

connected.

● The UPS is deleted on

the ECC800-Pro

WebUI.

● Reconnect the UPS

communications

cable.

● Reconnect the UPS

parallel cable.

● Remove the network

cable from the MON1

port on the UPS,

reinstall the cable,

and add the UPS on

the ECC800-Pro

WebUI.

The UPS does not report

a fault but has no output

voltage.

The output cable is not

properly connected.

Check the output power

cable connection.

The UPS does not start
after you press

is not pressed long

enough.

Press

for more than

5 seconds until you hear

a beep sound.

The UPS is overloaded.

Shut down all loads, and

restart the UPS.

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

368

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands