Huawei V100R021C00 User Manual Download

Page: 388 / 508

Component

Alarm Name

Alarm

Severit

Possible Cause

Measures

UPS

Rectifier fault

Critical

● The mains has

experienced a

transient high

voltage.

● The output carries

special loads such as

the inductive and

rectification loads.

● The output carries

the transformer load

but the transformer

mode is not enabled.

● The hardware is

damaged.

● Rectify the fault, and

power on the UPS

again.

● Check that the load

types are supported

by the UPS.

● Enable the

transformer mode.

● Contact Huawei

technical support.

Internal fault

Critical

The bypass input cable

connection does not

match the output

system.

Correct the bypass input

cable connection so that

it matches the output

system.

Fan fault

Critical

The fan is abnormal.

Clean up foreign matter

around the fan. If the

fault persists, contact

Huawei technical

support.

Inverter fault

Critical

The inverter output

short-circuits.

Eliminate the short

circuit at the output

port cable connection,

and then power on and

start the inverter again.

If the fault persists,

contact Huawei

technical support.

Output short

circuit

NOTE

The system

immediately

disconnects the

power output.

Critical

The load or cable is

short-circuited.

Locate and rectify the

short circuit.

Intelligent

battery

monitoring

system

Communication

Failure

Critical

The network cable

communication is

interrupted.

Check the cable

connection to the smart

ETH gateway.

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

376

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands