Huawei V100R021C00 User Manual Download

Page: 402 / 508

Component

Alarm Name

Alarm

Severit

Possible Cause

Measures

Comp LP switch

Major

1. The refrigerant leaks.
2. The solenoid valve is

faulty.

3. The cables to the LP

Switch are loose or

damaged.

4. The LP Switch is

damaged.

5. The dryer filter is

blocked.

6. The expansion valve

is blocked.

7. The indoor fans are

faulty.

1. Check for any

leakages. Fill

refrigerant after

maintenance or

replacement.

2. Maintain or replace

the solenoid coil or

the solenoid valve.

3. Check the cables to

the LP Switch.

4. Calibrate or replace

the LP Switch.

5. Maintain or replace

the dryer filter.

6. Maintain or replace

the expansion valve.

7. Maintain or replace

the indoor fans.

Comp LP switch

lock

Critical

The comp suction LP

alarm is generated

frequently.

Reference to the

solutions for the comp

suction LP alarm.

Gas pipe temp.

sensor fault

Major

1. Cables to the

temperature sensor

are not properly

connected.

2. The temperature

sensor is faulty.

1. Check cables to the

temperature sensor.

2. Maintain or replace

the temperature

sensor.

Compressor

preheating alarm

Warnin

The compressor heating

belt is preheating the

compressor oil.

Wait until the

preheating is complete

or manually stop

preheating in the

Setting menu.

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

390

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands