Huawei V100R021C00 User Manual Download

Page: 486 / 508

Figure 6-64 Sensor positions

(1) Smoke detector

Procedure

Step 1 Remove the smoke detector from the base.

Step 2 Remove the cables from the smoke detector and apply insulation measures such

as wrapping the cables with insulation tape to avoid hazards.

Step 3 Install the new smoke detector and reconnect the cables to the new smoke

detector.

Step 4 Install the smoke detector on the base.

Step 5 Blow smoke towards the smoke detector using a smoke pistol until the smoke

detector indicator changes from blinking once every 6s to steady on. If a smoke

detector fire alarm is triggered, the smoke detector is functional.

----End

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

474

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands