Huawei V100R021C00 User Manual Download

Page: 499 / 508

Context

Figure 6-81 Emergency door release button

Procedure

Step 1 Remove the emergency door release button.

1. Remove the screw that secures the emergency door release button, as shown

by (1) in

Figure 6-82

2. Remove the glass panel of the emergency door release button, as shown by

(2) and (3) in

Figure 6-82

3. Remove the screws that secure the base, as shown by (4) in

Figure 6-82

4. Disconnect cables and remove the emergency door release button.

Figure 6-82 Removing an emergency door release button

Step 2 Install a new emergency door release button.

1. Connect cables.
2. Tighten screws on the base, as shown by (1) in

Figure 6-83

3. Install the glass panel, as shown by (2) and (3) in

Figure 6-83

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

487

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands