background image

4.2.9.3 (Optional) Installing a LAN Switch

Context

The LAN switch needs to be installed in the 38 U position on the top of the front

of the IT cabinet to the right of the Converged Cabinet.

Figure 4-103 Position for the LAN switch

Procedure

Step 1 Locate the LAN switch installation position in the IT cabinet, and install guide rails

and floating nuts.

Step 2 Install the mounting ears delivered with the LAN switch, and secure the LAN

switch to the rack rails in the front of the cabinet.

NO TE

This section describes only the installation method. The actual product appearance prevails.

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

172

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Reviews: