Huawei V100R021C00 User Manual Download

Page: 210 / 508

Figure 4-149 Connecting the water detector

Step 4 Plan the installation position for the fastener of the water detection cable. Ensure

that the water detection cable placed on the fastener is in good contact with the

floor.

Step 5 Tear off the protection paper from the rear of the fastener, and then securely

attach the fastener to the floor.
●

If the fastener cannot be securely attached to the floor, perform

Step 6

●

If the fastener can be securely attached to the floor, perform

Step 7

Step 6 Drill holes in the floor with the same dimensions as the expansion bolts for the

fastener. Use the expansion bolts to secure the fastener to the floor, as shown in

Figure 4-150

Figure 4-150 Installing fasteners

NO TICE

When laying out the water detection cable, ensure that the water detector is close

to the Converged Cabinet to facilitate further cable connections.

Step 7 Place the water detection cable onto the fastener, secure the fastener, and keep

the water detection cable in close contact with the floor, as shown in

Figure

4-151

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

198

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands