Huawei V100R021C00 User Manual Download

Page: 217 / 508

Figure 4-162 Installing the magnet

(1) Rubber pad

Step 7 (Optional) Adjust the magnet.

1. If the magnet cannot attract the door properly after power-on, place a

magnetized metal part near the magnet to check whether the magnet

provides a proper magnetic force.

2. If the magnetic lock and the magnet do not work properly, check and

troubleshoot the circuit.

----End

4.2.9.13 (Optional) Installing an In-Room Single Door Magnetic Lock

Prerequisites

●

Verify that the room door is a revolving single-swing wooden door, and that

the door frame is wider than 42 mm.

●

The cable routes are planned.

Context

●

The BOM number of a single door magnetic lock is 02070081.

●

A single door magnetic lock is installed on a room door.

Procedure

Step 1 Fold the cutout template delivered with the device 90 degrees along the dotted

line, as shown by (2) in

Figure 4-163

Step 2 Close the door, place the cutout template near the door top at the far end of the

door axis, mark the mounting holes, and drill holes, as shown in

Figure 4-163

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

205

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands