Huawei V100R021C00 User Manual Download

Page: 227 / 508

For the detailed installation method, see documents delivered with the camera.

4.3 Cable Routing

4.3.1 System Cabling Rules

Attaching Cable Labels

NO TICE

A cable label must be consistent with the corresponding IT cabinet number.

Find the corresponding cable based on the wiring diagram in the cable fitting bag,

and attach the corresponding cable label taken out from the cable fitting bag to

both ends of the cable by wrapping the ends.

NO TE

The cable labels must completely wrap the cable without wrinkles.

Attach the cable labels 20 mm away from the plug except for special

circumstances. For example, a label shall not be attached to the bending part of a

cable or attached in some positions that may affect cable installation. If a label

conflicts with a cable tie, attach the label to the outer side of the cable tie.
Attach labels to both ends of a cable.

Requirements for Neatly Routing and Binding Cables

To route and bind cables in an appealing way, follow these rules:
1. Neatly organize exterior cables in a large bundle of cables and prevent cable

tangles that are avoidable, as shown in

Figure 4-178

Figure 4-178 Neatly organizing cables

FusionModule800 Smart Small Data Center

User Manual

4 Installation Guide

Issue 01 (2021-02-05)

215

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands