Huawei V100R021C00 User Manual Download

Page: 283 / 508

NO TE

– After the first login, change the password in time to ensure account security and

prevent unauthorized network attacks, such as data tampering. Huawei will not be

liable for any security issues caused by your failure to change the preset password

in time or password loss after changing.

– Change the password of the user account periodically.
– Record and keep the password properly. If you forgot the password, you will be

unable to log in to the WebUI.

– When the event notification is configured and the password retrieval mode is

configured under user management, the password can be retrieved.

– An account is logged out due to timeout if no operation is performed within 10

minutes after system login.

– A maximum of three users can log in to the ECC800-Pro WebUI at the same time.

----End

5.3.2 Preparations and App Login

Prerequisites

App operating environment requirements:
●

The mobile device must run Android 4.0 or later and is not root operating

system (the operating system is not flashed).

●

The mobile device has sufficient battery reserve.

●

You have obtained the IP address of the ECC800-Pro as well as the user name

and password used for WebUI login.

●

A PC with an IP address in the same network segment as that of the ECC800-

Pro is prepared, and the PC has connected to port WAN1 on the ECC800-Pro.

Procedure

Step 1 Download and obtain the app installation package using any of the following

three methods:
●

https://a.vmall.com/

), search for

FusionModule, and tap Download.
a. (Optional) Set the pad language to English.
b. Open the browser on the pad, enter

www.baidu.com

in the address box,

search for Huawei AppGallery, select Ordinary Download, and tap

Save.

Install the Huawei AppGallery. If the downloaded file exists in the drop-

down list box, tap the file to install the Huawei AppGallery. If the

downloaded file does not exist in the drop-down list box, choose File >

Local on the desktop, find the Download folder, and tap the Huawei

AppGallery installation package.

FusionModule800 Smart Small Data Center

User Manual

5 Power-On Commissioning

Issue 01 (2021-02-05)

271

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands