Huawei V100R021C00 User Manual Download

Page: 313 / 508

Parameter

Description

I-frame interval

This parameter is available only when you set Encoding

protocol to H.264 or H.265.
An I frame is an intra-coded frame that represents a

fixed image independent of other picture types. Each

group of pictures (GOP) begins with this type of frame.

A smaller I-frame interval indicates better video quality

and higher bandwidth consumption.

Layered

encoding

This parameter is available only when you set Encoding

protocol to H.264 or H.265.
To enable layered encoding, select Layered encoding.

JPEG quality

This parameter is available only when you set Encoding

protocol to MJPEG.
A larger value indicates higher image quality.

----End

Follow-up Procedure

Commission other cameras by referring to this section.

5.3.11.3.2 Commissioning a C3220 Camera (SD Card Configured)

Context

If the VCN or IVS1800 is not configured and an SD card is chosen, perform the

following procedure.

Procedure

Step 1 Log in to the Huawei camera WebUI.

1. Configure the PC IP address and the camera IP address in the same network

segment. Enter the camera IP address (192.168.0.120 by default) in the

address bar of the Internet Explorer and press Enter.

2. Enter the preset user name admin and the preset password HuaWei123, and

click Log In.

Step 2 For details about how to commission the camera and set parameters, see the

documents delivered with the device or the documents obtained by referring to

the "Preparing Documentation" section.
1. Preview the site situation in real time and check the camera coverage through

videos. Adjust the lens if necessary.

2. Set IPv4 address, IPv4 subnet mask, and IPv4 gateway address to the

planned values.

FusionModule800 Smart Small Data Center

User Manual

5 Power-On Commissioning

Issue 01 (2021-02-05)

301

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands

Huawei V100R021C00, User Manual

Search results

Summary of Contents for V100R021C00

Reviews:

Related manuals for V100R021C00

Brands by name

Popular brands