background image

6.4.2 Replacing Power Supply and Distribution System

Components

D ANGER

● Only qualified personnel can replace components of the power supply and

distribution system.

● Wear protective tools such as insulation gloves and shoes before replacing a

power supply and distribution component.

● Power off the upper-level equipment before replacing a power supply and

distribution component.

● Use a multimeter and electrical tester pen to check whether the front and rear

ends of the component to be replaced are powered off after the component is

powered off.

6.4.2.1 Replacing a Surge Protection Module

Prerequisites

D ANGER

● Do not replace a surge protection module during a thunderstorm.
● Before replacing a surge protection module, wear insulation gloves.

Tools: insulation protective gloves, electroprobe

Material: A new surge protection module of the same model is available and

functional.

Procedure

Step 1 Switch the SPD circuit breaker to OFF.
Step 2 Remove the protective panel from the SPD.

Figure 6-3 Removing the protective panel

FusionModule800 Smart Small Data Center

User Manual

6 O&M

Issue 01 (2021-02-05)

Copyright © Huawei Technologies Co., Ltd.

401

Summary of Contents for V100R021C00





























































































































































































































































































































































































































































































































Reviews: