Huawei V300R001 Parts Replacement Download

Page: 186 / 228

Check the status of the parts to be replaced.
Start SmartKit and choose

Home

Storage

Parts Replacement

Parts

Replacement

. On the

Parts Replacement

page, click

FRU Replacement

. Then

complete the check before the replacement as prompted. For details, see

5.1.3 Replacing

an FRU

You can proceed to next steps only when all items pass the pre-replacement check and the
replacement page is displayed. If any item fails, rectify the fault as prompted.

Step 2

Wear an ESD wrist strap.

Step 3

Press latches on the expansion module to release the handles and pull out the expansion
module, as shown in

Figure 5-100

Removing an expansion module

Step 4

Place the removed expansion module into an ESD bag.

Step 5

Take the spare part out of its ESD bag.

Step 6

Open the handles of the spare part, insert it into the empty slot, and close the handles, as
shown in

Figure 5-101

OceanStor Dorado V3 Series
Parts Replacement

5 Replacing FRUs

Issue 05 (2019-01-30)

178

Summary of Contents for V300R001





































































































































































































































Search results

Summary of Contents for V300R001

Reviews:

Related manuals for V300R001

Brands by name

Popular brands

Huawei V300R001, Parts Replacement

Search results

Summary of Contents for V300R001

Reviews:

Related manuals for V300R001

Brands by name

Popular brands