Huawei V300R001 Parts Replacement Download

Page: 144 / 228

Step 6

Put the removed power module into an ESD bag.

Step 7

Take the spare part out of its ESD bag.

Step 8

Insert the BBU into the spare part until it clicks into place, as shown in

Figure 5-57

Installing a BBU

Step 9

Open the handle of the spare part, insert the spare part into the empty slot, and close the
handle, as shown in

Figure 5-58

NOTE

The procedure for installing a DC power module is the same as that for installing an AC power module.
This step uses the AC power module as an example.

OceanStor Dorado V3 Series
Parts Replacement

5 Replacing FRUs

Issue 05 (2019-01-30)

136

Summary of Contents for V300R001





































































































































































































































Search results

Summary of Contents for V300R001

Reviews:

Related manuals for V300R001

Brands by name

Popular brands

Huawei V300R001, Parts Replacement

Search results

Summary of Contents for V300R001

Reviews:

Related manuals for V300R001

Brands by name

Popular brands