Huawei V300R001 Parts Replacement Download

Page: 149 / 228

Step 3

Remove the power cable.

Remove the AC power cable.

Loosen the retention clip, as shown in step 1 in

Figure 5-62

Removing the AC power cable

Pull up the retention clip, as shown in a of step 2 in

Figure 5-62

Remove the AC power cable, as shown in b of step 2 in

Figure 5-62

Remove the DC power cable.

Turn off the circuit breaker which connects to the DC power module.

Remove the protective cover on the DC power module, as shown in step 1 of

Figure 5-63

Removing the DC power cable

Unfasten the screws of the DC power cable with the Phillips screwdriver, remove
the shock absorption sheets, washers, and OT terminal round holes, as shown in
step 2 of

Figure 5-63

NOTE

When unfastening the screws from the DC power cable, prevent the shock absorption sheets
and washers from sliding off.

Install the protective cover on the DC power module, as shown in step 3 of

Figure

5-63

Step 4

Press the latch on the inner side of the power module handle and pull out the power module,
as shown in

Figure 5-64

NOTE

The procedure for removing a DC power module is the same as that for removing an AC power module.
This step uses the AC power module as an example.

OceanStor Dorado V3 Series
Parts Replacement

5 Replacing FRUs

Issue 05 (2019-01-30)

141

Summary of Contents for V300R001





































































































































































































































Search results

Summary of Contents for V300R001

Reviews:

Related manuals for V300R001

Brands by name

Popular brands

Huawei V300R001, Parts Replacement

Search results

Summary of Contents for V300R001

Reviews:

Related manuals for V300R001

Brands by name

Popular brands