Huawei V300R001 Parts Replacement Download

Page: 205 / 228

Figure 5-119

Removing a disk module

Hold the ejector lever, and pull out the disk module for about 3 cm (1.18 in.). See step
(2) in

Figure 5-119

. Wait for at least 30 seconds until the disk module stops working.

Then remove the disk module from the quorum server. See step (3) in

Figure 5-119

Place the removed disk module in an ESD bag.

Step 2

Install the spare part.

Take the spare part out of its ESD bag.

Fully raise the ejector lever and push the spare part into the chassis along the guide rails
until it does not move. See step (1) in

Figure 5-120

OceanStor Dorado V3 Series
Parts Replacement

5 Replacing FRUs

Issue 05 (2019-01-30)

197

Summary of Contents for V300R001





































































































































































































































Search results

Summary of Contents for V300R001

Reviews:

Related manuals for V300R001

Brands by name

Popular brands

Huawei V300R001, Parts Replacement

Search results

Summary of Contents for V300R001

Reviews:

Related manuals for V300R001

Brands by name

Popular brands