background image

 

6. List of Manufacturer Parameters

 

 

 

 

Parameter Item 

Initial 

Value 

Function 

System 

Parameters 

Air End  2 

Time 

000000 hrs 

Modify the total running time of Air End  2. 

 Fault History 

Reset 

0000 

Enter "8888" and confirm it to clear the fault 
history. 

Temperature 

Warning 

105

 

When Air End  2 temperature is higher than this set 
temperature, a warning will be given. 

Temperature 

Shutdown 

110

 

When Air End  2 temperature is higher than this set 
temperature, fault shutdown will be reported. 

Date 

9999-99-99 

Record the manufacture date of air compressor. 

Manufacture 

Number 

99999999 

Manufacture number of equipment entered by 
manufacturer. 

Phase 

Sequence 

Protection 

Disable / 

Enable 

Used to disable or enable the phase sequence 
protection. 

Frequency 

Selection 

50Hz/60Hz 

Select the working power frequency of air 
compressor. If set incorrectly, there will be a 
deviation in detected current value. 

Connection 

Method 

Advanced / 

Compatible 

Alternate 

High Voltage 

0000V 

When the controller detects that the voltage is 
higher than the set value, the machine will shut 
down for protection and a higher voltage is 
reported. When set to 0000, the high-voltage 
function is invalid. 

Low Voltage 

0000V 

When the controller detects that the voltage is 
lower than the set value, the machine will shut 
down for protection and a lower voltage is 
reported. When set to 0000, the low-voltage 
function is invalid. 

Low 

Temperature 

Protection 

-0005

 

When the controller detects that the exhaust 
temperature is lower than this value, it shows the 
temperature is too low, and the air compressor is 
not allowed to start. 

 

Time Limit 

0000 hrs 

When the air compressor has run for a time greater 
than the set time, it will shut down with a report of 
"use error"; when set to  0000, the time limit 
function is invalid. 

Summary of Contents for MAM860


















Reviews: