background image

 

Hubble Optics Ultra Light UL 16 
Dobsonian 

instruction manual

REV: 1.1.5 02-12-2013

Please read these instructions thoroughly before beginning assembly 
and subsequent use of the telescope.

1.Unpacking

 

                                                                                                                   

 

 

..................................................................................................................

 

 2  

2. Assembly

 

                                                                                                                    

 

 

...................................................................................................................

 

 7  

2.1 Install the Secondary Mirror 

 

                                                                                 

 

 

................................................................................

 

 8  

2.1.1 Install the Secondary to the diagonal holder

 

                                                  

 

 

.................................................

 

 8  

2.1.2 Install the Secondary Mirror Cage

 

                                                                 

 

 

................................................................

 

 9  

2.2 Assembly of the Dobsonian Rocker

 

                                                                    

 

 

...................................................................

 

 14

   

2.3 Assembly of the Mirror Box

 

                                                                               

 

 

..............................................................................

 

 14

   

2.3.1 Installation of the Pads and Brass Wires 

 

                                                     

 

 

....................................................

 

 15

   

2.3.2.  Installation of the Lower ALT Bearing Sections

 

                                       

 

 

......................................

 

 16

   

2.4 Install The Truss Tubes and Secondary Cage

 

                                                     

 

 

....................................................

 

 22

   

2.4.1 Installation of the Truss Tubes

 

                                                                     

 

 

....................................................................

 

 22

   

2.4.2 Installation of the Secondary Mirror Cage

 

                                                   

 

 

..................................................

 

 24

   

2.4.3 Installation of the Optional Finder Scope

 

                                                     

 

 

....................................................

 

 26

   

2.5 Adjust the Sling

 

                                                                                                   

 

 

..................................................................................................

 

 27

   

3. Collimate the Optics.

 

                                                                                               

 

 

..............................................................................................

 

 28

   

4. Care and Maintenance

 

                                                                                            

 

 

...........................................................................................

 

 31

   

4.1 Mirror Storage

 

                                                                                                     

 

 

....................................................................................................

 

 31

   

4.2 Mirror Cleaning

 

                                                                                                   

 

 

..................................................................................................

 

 32

   

5. Specifications

 

                                                                                                           

 

 

..........................................................................................................

 

 33

   

6. Limited Warranty

 

                                                                                                   

 

 

..................................................................................................

 

 34

   

7. Technical Support

 

                                                                                                   

 

 

..................................................................................................

 

 34

   

 

WARNING: 

Never look at the sun with your telescope without a  

professionally made solar filter. Permanent eye damage or blindness  
could result. Eye damage is often painless, so there is no warning until  
it is too late. Children should not be allowed to handle the telescope.  
Avoid using the type of solar filter that screws into an eyepiece. They  
are susceptible to cracking under the intense heat that builds up near  
the focus point, and could cause severe retinal damage. Use only the  
type of solar filter that covers the front of the telescope. Also, be sure to  
leave the cover caps on the finder scope when solar observing. Better  
yet, remove the finder scope altogether when viewing the sun.

1

Summary of Contents for Ultra Light UL 16



































Reviews: