background image

 

© 

2011 by Huchez Treuils S.A.S.

 

Translation of the original instructions manual

 2

UK 

Reproduction prohibited

 

To ensure the constant improvement of its products, HUCHEZ reserves the right to change the equipment as 

described below and, in this case, to supply products which differ from the illustrations in this instruction manual. 

Reproduction prohibited 

 

Sommaire 

1 - Conditions for use .................................................................................................  

 

2 - Safety instructions ................................................................................................  

 

3 - Warranty ..............................................................................................................  

4 - Acceptance of the equipment ................................................................................  

5 - Obligatory regulatory checks by the user .............................................................  

6 - Presentation of the machines ...............................................................................  

 

7 - Handling – Storage ...............................................................................................  

8 - Installation and set-up .........................................................................................  

9 - Servicing and maintenance ...................................................................................  

14 

10 - Taking out of use ................................................................................................  

15 

11 - Spare parts .........................................................................................................  

16 

12 - Operating faults ..................................................................................................  

16 

13 - Declaration of EC conformity ..............................................................................  

17 

14 - Appendices .........................................................................................................  

18 

 
 

1 - Conditions for use 

All  users  must  read  the  set-up  instructions  carefully  before  using  the  product  for  the  first  time. 
These instructions should enable the user to familiarise themselves with the winch and use it to its 
full  capacity.  The  set-up  instructions  contain  important  information  about  how  to  use  the  winch 
safely and correctly. Compliance with these instructions helps to avoid danger, reduce repair costs, 
reduce  stoppage  time  and  improve  the  reliability  and  service  life  of  the  winch.  The  instruction 
manual  must  always  be  available  in  the  place  where  the  winch  is  being  used.  In  addition to the 
set-up  instructions  and  regulations  concerning  the  prevention  of  accidents,  the  work  safety  and 
professional regulations in force in each country must also be respected. 
 
This  equipment  is  governed  by  European  regulations  and  more  specifically Directive  2006/42/EC 
on machinery, Directive CEM 2014/30/UE, BT 2014/35/UE and RED 2014/53/UE as well as the EN 
14492/1 standard. 

 

These winches are designed to move loads using a suitable steel rope. They have been designed to 
perform lifting and pulling operations within the defined load capacity limit and with safety factor 5 
(static against sudden failure). 

 

 

For use in lifting, the European regulation makes certain equipment obligatory, such as a limit 
switch system and, for loads of 1,000 kg or more, a load limiter. 

 

The  operator  must  check  the  presence  of  this  equipment  (available  as  an  option  from  the 
manufacturer) before using the product for lifting purposes. 

 

The capacity indicated on the winch corresponds to the maximum capacity of use (MCU); in no 
event should this capacity be exceeded. 

 

T

HIS WINCH MUST NOT

,

 UNDER ANY CIRCUMSTANCES

,

 BE USED TO LIFT PEOPLE

 

Do  not  begin  moving  the  load  until  you  have  attached  it  correctly  and  checked  that  all 
personnel are outside the danger zone. 

Summary of Contents for PRIMO INOX BT 1000



























Reviews: