background image

212

Series Tooling                                                                                  Alcoa Fastening Systems

10

M

AINTENANCE

Good Service Practices

The efficiency and life of any tool depends upon
proper maintenance and good service practices.
Tool should be serviced by personnel who are
thoroughly familiar with it and how it operates.

A clean, well-lighted area should be available for
servicing the tool. Special care must be taken to
prevent contamination of pneumatic and
hydraulic systems. Proper hand tools and soft
materials to protect tools must be available. Only
standard hand tools, brass drift and wood block
are required. Vise with soft jaws should be avail-
able. See 

Table 2

for tools available from

Huck.

ALWAYS REPLACE ALL SEALS AND BACK-
UP RINGS WHEN TOOL IS DISASSEMBLED
FOR ANY REASON.

All parts must be handled carefully and exam-
ined for damage and/or wear. Components
should be disassembled and assembled in
straight line without bonding, cocking or undue
force. 

DISASSEMBLY

and 

ASSEMBLY 

proce-

dures outlined in this manual should be followed.

Rub SLIC-TITE TEFLON* thread compound, or
equivalent, on pipe plug threads and quick con-
nect fitting. 

CAUTION: Do not use Teflon tape

on pipe threads. Pipe threads may cause tape
to shred, resulting in tool malfunction. SLIC-
TITE, 503237, is available in stick form from
Huck. 

Smear LUBRIPLATE 130AA*, or equiva-

lent, on seals (O-rings etc.) and mating surfaces
to aid assembly and to prevent damage to seals.
LUBRIPLATE 13OAA, 502723, is available in a
tube from Huck.

Use VIBRA-TITE* on Gland (29) threads.
VIBRA-TITE, 505125, is available from Huck.
Follow directions on bottle.

Apply LOCTITE Adhesive/Sealant to Nut,
505420. LOCTITE, 503657, - - in a tube - - is
available from Huck. Service Kit, 212KIT,
includes perishable parts and should be kept on
hand. Other components, as experience dictates,
should also be readily available for replace-
ments.

LUBRIPLATE is a trademark of Fiske Brothers Refining Co.

TEFLON is a trademark oF E. I. DuPont de Nemours & Co.

VIBRA-TITE is a trademark of the Oakland Corporation.

LOCTITE  is a trademark of Loctite Corp.

Summary of Contents for ALCOA 212



































Reviews: