background image

11

SF32 BobTail® Installation Tooling 

(HK1180)

         

                       

 Alcoa Fastening Systems & Rings

h

ydraulIC

 C

ouplIngs

f

Igure

 5

504438

 O-ring

501102

 Back-up Ring

Use a fine India stone to remove any nicks or burrs from diameter 

A

 and 

leading edge to prevent damage to O-ring.

Thiese tools come labeled with important stickers that contain safety and pressure settings information. It is 

necessary that these stickers remain on the tools and are easily read. If stickers become damaged or worn, or if 

they have been removed from the tool, they must be replaced. The part numbers are shown in the tool assembly 

drawing of this manual.

s

tICker

 l

oCatIons

o

ptIonal

 e

quIpment

TEFLON

®

 Stick

 - 

503237

TEFLON

®

 Sealant

 - 

620012

Loctite

®

 243

 - 

508567

Never-Seez

®

 NS-160 

- 505565 

(anti-seize and lubricating compound)

LUBRIPLATE

®

 130-AA 

-  502723

Threadmate™ 

(4oz. tube)

 

- 508517

Pressure Gage 

-  T-124833CE

Service Kit 

-  SF32KIT

Swage Gage 

-  HG-S-MBT20 

(20mm)

 

 

 HG-S-BT24 

(3/4”)

Hose Assembly 

 

Hose Length

 

Part No.

(Contains 2 identical

 - 

6 ft

  

118309-6

hydraulic hoses with

 - 

12 ft

  

118309-12

one male and one female 

- 2

6 ft

  

118309-26

quick connect fitting at

 - 

38 ft

  

118309-38

each end)

 - 

52 ft

  

118309-52

Loctite

 is a registered trademark of Henkel Corporation, U.S.A..

Never-Seez

 is a registered trademark of Bostik, Inc.

LUBRIPLATE

 is a registered trademark of Fiske Brothers Refining Co.

Threadmate

 is a registered trademark of Parker Intangibles LLC..

TEFLON

 is a registered trademark of E. I. du Pont de Nemours and Company.

Summary of Contents for BobTail SF32

















Reviews: