background image

5

Introduction

ASHES:

 Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container 

of ashes should be stored on a non-combustible floor, well away from all combustible materials pending 

final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispensed, they should be 

retained in the closed container until all cinders have been thoroughly cooled.

ELECTRICAL:  The  use  of  a  surge  protected  power  bar  is  recommended. 

The  unit  must  be 

grounded. The grounded electrical cord should be connected to a standard 115 volts (3.3 Amps), 60 

hertz electrical outlet.  Be careful that the electrical cord is not trapped under the appliance and that it is 

clear of any hot surfaces, sharp edges, and is accessible. If this power cord should become damaged, a 

replacement power cord must be purchased from the manufacturer or a qualified HUDSON RIVER dealer. 

This unit’s maximum power requirement is 400 watts.

GLASS:

 Do not abuse the glass by striking or slamming the door.  Do not attempt to operate the stove 

with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an HUDSON 

RIVER dealer.  Do not attempt to open the door and clean the glass while the unit is in operation or if 

glass is hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass 

cleaner, or take a damp paper towel and dip into the fly ash. This is a very mild abrasive and will not 

damage the glass.

FLAMMABLE  LIQUIDS:

 

Never 

use  gasoline,  gasoline-type  lantern  fuel,  kerosene,  charcoal  lighter 

fluid, or similar liquids to start or “freshen up” a fire in the heater.  Keep all such liquids well away from 

the heater while it is in use.

SMOKE  DETECTOR:

  Smoke  detectors  should  be  installed  and  maintained  in  the  structure  when 

installing and operating a pellet burning appliance.

OPERATION:

 The ash pan, door, and hopper lid must be closed securely for proper and safe operation 

of the pellet stove. Ensure all gaskets and seals are checked regularly and replaced when necessary.  

KEEP ASH PAN FREE OF RAW FUEL. 

DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN THE ASH PAN. A FIRE IN THE ASH PAN MAY 

OCCUR.

INSTALLATION:

 Be sure to maintain the structural integrity of your home when passing a vent through 

walls, ceilings, or roofs. It is recommended that the unit be secured into its position in order to avoid any 

displacement.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

FRESH AIR:

 Outside Fresh Air connection is optional BUT MUST be connected to all units installed in 

Mobile and “Air Tight Homes” (R2000) or where required by local codes. Consider all large air moving 

devices when installing your unit and provide room air accordingly. Limited air for combustion may result 

in poor performance, smoking and other side effects of poor combustion.

If you have any questions with regards to your stove or the above-mentioned information, please feel 

free to contact your local dealer for further clarification and comments.

SINCE  HUDSON  RIVER  STOVE  WORKS  HAS  NO  CONTROL  OVER  THE  INSTALLATION  OF 

YOUR STOVE, HUDSON RIVER STOVE WORKS GRANTS NO WARRANTY IMPLIED OR STATED 

FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, HUDSON RIVER 

STOVE WORKS ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

Summary of Contents for KINDERHOOK




































Reviews: