background image

The customer will need this information if they ever need to contact their service provider
for assistance. If no printer is available, advise the customer to record this information and
make sure they know where it is recorded. Make sure the customer knows where this
information is recorded.

4.

Click

Continue

to download configuration parameters to the router.

A second Registration in Progress screen appears briefly (not shown here) while the
configuration parameters are downloaded. Then the Registration Complete screen appears.

5.

Click

Restart

on the Registration Complete screen.

This restarts the satellite router.

Figure 43: Registration complete – restarting the router

The Terminal Reset screen appears. (It is not shown here.)

6.

Click

Close

on the Terminal Reset screen.

The router is now commissioned.

Manual commissioning

If satellite-based commissioning is not available, you must commission the router manually.
However, do not use the manual commissioning method unless you are instructed to do so by
the service provider.

Manual commissioning requires coordination between you and the Network Operations Center
(NOC). A technician enters parameters at the NOC, and you enter the same parameters at the
installation site. The NOC also downloads encryption keys and certain parameters to the router.
Manual commissioning process consists of:

• Entering manual commissioning parameters
• Antenna pointing

For both tasks you use the satellite router’s web-based interface.

HN9400 Satellite Router Installation Guide

52

1038554-0001 Revision B

Commissioning the satellite router

Chapter 4

Summary of Contents for HN9400







































































































































Reviews: