background image

-5-

3. 

Cautions

Warning

Do not place flammable materials near the equipment. Fire may occur.

Do not touch the power cord with wet hands. Electric shock may occur .

Do not plug too many equipment into the same electric outlet. Overload may 

cause a fire..

Make sure to connect a ground wire. Electric shock may occur without a 

ground wire.

Caution

Before plugging into the electric outlet, make sure that the power voltage is 

220VAC, 50/60Hz.

Avoid using other electric equipment with high voltage current near this 

equipment. 

Do not pour water on this equipment directly. 

A short circuit may occur. .

Do not use acid solution, benzene, and sharp objects, to clean the equipment. It 

may cause changes of color or damage. Rubber and plastic parts are likely to 

change easily. Do not use any volatile material. If you use any detergent, clean it 

with water thoroughly 

Unplug from an outlet by holding the plug. Do not unplug it by pulling on the 

power cord.

If this unit is not going to be used for a long period of time, remove the plug 

from an outlet.

Damaged power cord can cause a short circuit or a fire.

Avoid putting too many objects in the chamber. 

It will block normal air circulation.

Danger

Do not put flammable, explosive materials in the chamber. Explosion or fire 

may occur due to improper handling.

MUFFLE FURNACE

Summary of Contents for DMF-05



















Reviews: