background image

 

 
Thank you for choosing Humminbird, America’s #1 name in depthsounders. Humminbird has built 
its reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment. 
Your Humminbird is designed for trouble-free use in even the harshest marine environment. 
 
In the unlikely event that your Humminbird does require repairs, we offer an exclusive Service 
Guarantee – free of charge during the first year after purchase, and available at a reasonable rate 
after the one –year period. Complete details are included at the end of this manual. 
 
We encourage you to read this operations manual carefully in order to get full benefit from all the 
features and uses of your Humminbird product. Also, to register your purchase and help us learn 
more about you, please fill out the warranty registration card at the back of this manual. 
 
WARNING! This device should not be used as a navigational aid to prevent collision, grounding, 
boat damage, or personal injury. When the boat is moving, water depth may change too quickly 
to allow time for you to react. Always operate the boat at very slow speeds if you suspect shallow 
water or submerged objects. 
 

 

TABLE OF CONTENTS 

 
 
Section 1: GENERAL INFORMATION 
How Sonar Works 
Transducer Exchange 
 
Section 2: INSTALLATION 
Parts Supplied 
Transducer Installation 

Summary of Contents for HDR 600

















Reviews: