background image

INSTALLATION 

TRANSOM INSTALLATION 

 

Step Six - Route the Cable 

 
There are several ways to route the transducer cable to the to the area where the 
control head will be installed. The most common procedure routes the cable 
through the transom into the boat. 

 

Inside the boat there is often a channel or conduit used for other 
wiring that the cable can be routed along. Do not cut or shorten 
the transducer cable and try not to damage the cable insulation. 
Route the cable as far as practical from the VHF radio antenna 
cables or tachometer cable to reduce the possibility of 
interference. 

 

If the cable is too short, extension cables are available to extend 
the transducer cable up to a total of 50' (15 m). Call Humminbird 
Customer Support for more information. 
 
Follow these steps to route the cable through the transom: 

 

1.  Drill a 5/8” (16mm) hole above the water line. Route the 

cable through the hole. 

 

2.  Fill the hole with silicone sealant. 

 

3.  Place the escutcheon plate over the hole and attach with the two #8 x 5/8” 

(16mm) screws. 

 

4.  Secure the cable by attaching the cable camp to the transom using a #8 x 

5/8” (16mm) screw. 

 

Note:  The transducer will pivot up to 90 degrees in the bracket. Allow 
enough slack in the cable for this movement. It is best to route the cable to 
the side of the transducer so the cable will not be damaged by the 
transducer during movement. 

 

Summary of Contents for LCR W































Reviews: