background image

WHAT YOU SEE ON-SCREEN 
 
 

 
 

The first thing you may 

notice about the LCR W unit is 
the high resolution screen LCD 
display. The LCD display uses 
super-twist technology, for 
maximum viewability and is 
ruggedized for tough shock and 
vibration endurance. The 
display can operate at 
temperatures more extreme 
than you are likely to encounter. 
 
 

There are two basic 

screen layouts for the LCR W. 
Figure A shows the default 

screen layout which does not include temperature and speed readings. If you have purchased the 
temperature and speed accessory and it is installed, the screen layout will be slightly different as 
shown in Figure B. 

 
 

The number of vertical pixels (picture elements or dots) in 

a given depth range determines the display resolution, or ability to 
differentiate targets close to the bottom or other targets. The LCR 
W is capable of distinguishing between targets only 6 inches 
apart, and show fish within 6 inches of the bottom. 
 
 

On all screens the horizontal line at the top of the display 

is the "Zero" line. This represents the surface of the water. The 
"Zero" line will always have a gap which moves as the screen 
updates. This gap lets you know that the display is updating 
even if the bottom terrain remains the same or is not visible on 
the selected depth range. The farthest right column of information 
is the most recent information, and it shows what is directly under 
your boat. 
 

 
 

At power-up, the LCR W locates 

the bottom and adjusts the depth range to 
a setting most appropriate for that depth. 
The bottom will be usually shown about 2/3 
of the way down the display. The Structure 
ID T"^ depiction of the bottom will vary in 
appearance depending on the bottom 
terrain. If the bottom is very hard and 
smooth, the bottom depiction will be narrow 
and dense. If the bottom is mud or soft 
sand, the bottom depiction will be thick and 
less dense. This indicates that much of the 
sonar signal is absorbed by the soft 
bottom. If the bottom is rugged and varying, 
such as a rocky bottom, the depiction will 
be textured and vary in density. Structure, 
such as submerged trees or brush, or other objects are clearly displayed above the solid bottom 

Summary of Contents for LCR W































Reviews: