background image

 
The zoom range is determined by the depth range in use when zoom is enabled. In shallow 
water, when the 15' or 30' depth range is used, the zoom range will be 7-1/2'. If the 60' or 120' 
depth range is in use, the zoom range will be 15', if a 180' to 480' depth range is used, the zoom 
range will be 30', and if the 600' range is in use, the zoom range will be 60'. 
 
To enable zoom, adjust the depth of the zoom range first using 
the UP and DOWN Arrow buttons until the upper and lower limit 
numbers correspond with the range you wish to view, then 
enable Zoom using the ENTER button. 
 
Once you are in Zoom, you may still adjust the depth of the 
zoom range by using the UP and DOWN Arrow buttons. The 
Zoom menu will not appear when an adjustment is made unless 
MENU is pressed. 
 
The digital depth readout will continue to track the bottom even 
when Zoom is enabled. 
 
Bottom Lock is a function of Zoom, except the depth adjustment 
is controlled automatically to view the area immediately above 
the bottom. This is especially useful if you are looking for 
structure or minor variations in terrain in areas of relatively flat 
bottom terrain. To enable Bottom Lock, press ENTER until the BL is highlighted. The Zoom range 
will be controlled by the current depth range, as in Zoom, and will be indicated on the Zoom 
menu. 
 
 
 
 

Bottom Alarm 

 
The Wide Eye contains an audible alarm to warn you of shallow water depths. This alarm is 
adjustable from 2' to 99' of depth. To enable the alarm, simply adjust the alarm depth using the 
UP and DOWN arrow buttons, and press ENTER. Whenever the depth of the water beneath your 
boat is equal to or less than the selected alarm depth, a continuous alarm will sound. 
 

 

 
To disable the alarm, either move to deeper water, or select the Bottom Alarm menu, and press 
ENTER to turn the alarm off. 
 

Summary of Contents for Wide Eye

































Reviews: