background image

13

45051-01  •  05/12/11  •  Hunter Fan Company

Problem:  Nothing happens; fan does not move.

1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the 

fan section.

3. Check the plug connection in the switch housing.
4. Push motor reversing switch firmly left or right to ensure that the 

switch is engaged.

5. Pull the pull chain to ensure it is on.
6. Remove the shipping bumpers.

Problem:  Noisy operation.

1. Tighten the blade assembly screws and blade iron armature screws 

until snug.

2. Check to see if the blade is cracked.  If so, replace all the blades.

Problem:  Excessive wobbling.

1. If your fan wobbles when operating, use the enclosed balancing kit 

and instructions to balance the fan.

2. Tighten all blade iron screws.
3. Turn power off, support fan very carefully, and check that the 

hanger ball is properly seated.

If you need parts or service assistance, please call 
888-830-1326 or visit us at our website at 

 

http://www.hunterfan.com.

Hunter Fan Company
7130 Goodlett Farms Pkwy. #400
Memphis, Tennessee 38016

8 • Troubleshooting

Summary of Contents for 21781















Reviews: