Hunter 28789 Owner'S Manual Download

Page: 12 / 16

45086-01 • 09/22/2011 • Hunter Fan Company

Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).
7-1. Your fan may include blade grommets. If your fan has grommets,

insert them by hand into the holes on the blades.

7-2. Attach each blade to a blade iron using three blade assembly

screws. If you used grommets, the blades may appear slightly loose
after screws are tightened. This is normal.

7-3. Remove the blade mounting screws and rubber shipping bumpers

from the motor.

Note:

Some blade mounting screws are installed

in the motor to secure shipping blocks.

7-4. For each blade, insert one blade mounting screw through the

blade iron, and attach lightly to the fan. Insert the second blade
mounting screw, then securely tighten both mounting screws.

Step 7-1 (Detail)

Blade Assembly

Screws

Use with grommet

Use without grommet

Grommet

Blade

Mounting

Screw

Steps 7-1 – 7-2

Step 7-4

7 • Assembling the Blades

Summary of Contents for 28789

















Search results

Summary of Contents for 28789

Reviews:

Related manuals for 28789

Brands by name

Popular brands

Hunter 28789, Owner'S Manual

Search results

Summary of Contents for 28789

Reviews:

Related manuals for 28789

Brands by name

Popular brands