background image

14

Hunter Fan Company 

42606-01 • 11/18/05

9 • Troubleshooting

Problem:  Nothing happens; fan does not move.

1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the 

fan section.

3. Check the plug connection in the switch housing.
4. Push motor reversing switch fi rmly left or right to ensure that the 

switch is engaged.

5. Pull the pull chain to ensure it is on.
6. Remove the shipping bumpers.

Problem:  Noisy operation.

1. Tighten the blade bracket screws until snug.
2. Tighten the blade screws until snug.
3. Check to see if the blade is cracked.  If so, replace all the blades.
4. Change to an approved speed control.
5. Be sure that the glass is secure.
6. Check and tighten the screws in the switch housing mounting 

plate and in the upper and lower switch housing.

Problem:  Excessive wobbling.

1. If your fan wobbles when operating, use the enclosed balancing kit 

and instructions to balance the fan.

2. Tighten all blade and/or blade iron screws.
3. Turn power off , support fan very carefully, and check that the 

hanger ball is properly seated.

If you need parts or service assistance, please call 
888-830-1326 or visit us at our Web site at 
http://www.hunterfan.com.

Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114

Summary of Contents for 42606-01















Reviews: