background image

4

Hunter Fan Company 

42606-01 • 11/18/05 

5

42606-01 • 11/18/05 

Hunter Fan Company

2 • Installing the Ceiling Plate

 

CAUTION:

 To avoid possible electrical shock, before installing your fan, 

disconnect the power by turning off the circuit breakers to the outlet box 
and associated wall switch location. If you cannot lock the circuit breakers 
in the off position, securely fasten a prominent warning device, such as a 
tag, to the service panel.

2-1.  Drill two pilot holes into the wood support structure through the 

outermost holes in the outlet box. e pilot holes should be 9/64” 
in diameter.

   

For Angled Ceilings:

 Be sure to orient the ceiling plate so that the 

two tabs are pointing towards the ceiling peak. 

2-2.  Your fan comes with four preinstalled noise isolators. Check to 

make sure all four isolators are in place and were not removed 
during shipment. 

2-3.  Place a flat washer on each of the two 3” wood screws. 
2-4.  read the supply wires from the outlet box in the ceiling through 

the hole in the center of the ceiling plate.

2-5.  Align the slotted holes in the ceiling plate with the pilot holes you 

drilled in the wood support structure. For proper alignment use 
slotted holes directly across from each other. 

   

Note:

 e isolators should be flush against the ceiling.

2-6.  Pass the screws through the slotted holes in the ceiling plate into 

the pilot holes you drilled. 

    Tighten the screws into the 9/64” pilot holes; do not use lubricants 

on the screws. Do not over tighten.

Flat Washer

3” Wood 

Screw

Steps 2-3 – 2-6

Ceiling 

Plate

For Angled Ceilings: 

Be sure to orient 

the ceiling plate so that the two tabs 
are pointing towards the ceiling peak. 

Towards 

Ceiling Peak

Summary of Contents for 42606-01















Reviews: