Hunter 5954-C54CFLK Instructions Manual Download | Manualshive

Page: 10 / 17

background image

www.HunterFan.com

1.888.830.1326

Blades

Insert grommets found in the hardware

bag into the holes in the blades, then

secure each blade to a blade iron with

screws found in the hardware bag.

Lightly attach the blade irons to the

motor with screws found in the

hardware bag, then securely tighten

after both screws are attached.

10

M0129-01 • 09/21/16 • © 2016 Hunter Fan Company

«
...
8
9
10
11
12
...
»

Summary of Contents for 5954-C54CFLK


















Reviews:

No comments

Related manuals for 5954-C54CFLK

Brand: S&P Pages: 24

Brand: Vectaire Pages: 10

Brand: Pollrich DLK Pages: 50

Brand: PASCO Pages: 4

Brand: Parker Pages: 38

Brand: NuAire Pages: 9

Brand: ATD Tools Pages: 7

Brand: ebm-papst Pages: 12

Brand: emerio Pages: 33

Brand: HAEGER Pages: 40

Brand: Sygonix Pages: 4

Brand: Fanaway Pages: 15

Brand: Air King Pages: 8

Brand: Vortice Pages: 80

Brand: U.S. FAN Pages: 4

Windward II 523 127

Brand: HAMPTON BAY Pages: 44

Brand: ebm-papst Pages: 5

ENERVENT+ EVT-09 Series

Brand: Ruskin Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands