9. The module is now ready to connect in the software.
10. Use an internet-connected computer or mobile device to
visit centralus.hunterindustries.com.
SOFTWARE SETUP
1. From the Main Menu icon in the
software, select Add Controller.
2. Follow the on-screen instructions to
add your controller. After entering the
required information, the software
will send a Controller Verification
Code for security purposes.
3. Go to the controller menu for
Settings and select Controller
Verification.
4. Enter the code number that appears at the Controller
Verification screen into the software setup screen.
5. If the Verification Code is correct, the controller will be
added to the software and the map.
6. The networking icon on the Home screen of the controller
should now display a green status icon.
DIRECT CONNECT
If you want to connect a Wi-Fi mobile device directly to the
controller (instead of through an internet server), dial to the
Settings menu and select Networking. Press the soft key
for Wi-Fi Setup and check the box for Direct Connect. For
additional information about direct connect functions, visit:
hunterindustries.com/support/a2c-using-acc2-wifi-direct-
connect
TROUBLESHOOTING
Network Test
The Network Test function will check all connections from the
controller, through the router, to the server. If the controller is
not communicating, this will indicate which functions are not
performing.
Note:
Sometimes, turning the controller power off and back on
can restore or fix network connections.
COMPLIANCE AND APPROVALS
Hunter Industries hereby declares that this product is in
compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU (Radio Equipment
Directive). Contact Hunter Industries for complete
compliance information.
FCC Notice
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the manufacturer’s instruction manual, may cause
interference with radio and television reception. This
equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.
Notice:
The FCC regulations provide that changes or
modifications not expressly approved by Hunter Industries
could void your authority to operate this equipment. These
limits are designed to provide reasonable protection against
harmful interference in a residential installation. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
•
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
•
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage, et
2. L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
RC-004-IG-A2CWIFI 8/19
RESIDENTIAL & COMMERCIAL IRRIGATION
|
Built on Innovation
®
Learn more.
Visit hunterindustries.com
For complete setup information, scan the QR code or visit hunterindustries.com.
© 2019 Hunter Industries Inc. Hunter, the Hunter logo, and all other trademarks are property of Hunter Industries,
registered in the U.S. and other countries.
