Hunter M0035-01 Instructions Manual Download

Page: 5 / 17

www.HunterFan.com

1.888.830.1326

M0035-01 • 05/28/13 • © Hunter Fan Company

Ceiling Bracket

OFF

Refer to warning w.1 on pg. 2

To avoid possible electrical shock, before

installing your fan, disconnect the power by
turning off the circuit breakers to the outlet

box associated with the wall switch location.

Turn P

Remove all four mounting isolators.

Align the tapered mounting holes in the
ceiling plate with the holes in the ceiling

bracket. Install the four ceiling plate

screws found in the hardware bag and

secure with the flange nuts using an 11/32”

wrench. Hold the ceiling bracket assembly

up to the outlet box and mark the screw

locations. To mount to support structure,

also mark the ceiling for drilling pilot holes.

Install the ceiling plate gasket onto the

ceiling plate. The four holes in the ceiling

plate should lineup with the four posts in

the gasket.

Tapered
Mounting
Holes

Ceiling
Plate
Gasket

Post

Ceiling
Plate

Flange
Nuts

Mounting
Isolator

Ceiling
Bracke

Ceiling Plate
Screws

Summary of Contents for M0035-01


















Search results

Summary of Contents for M0035-01

Reviews:

Related manuals for M0035-01

Brands by name

Popular brands

Hunter M0035-01, Instructions Manual

Search results

Summary of Contents for M0035-01

Reviews:

Related manuals for M0035-01

Brands by name

Popular brands