background image

5

41968-01  •  10/02/08  •  Hunter Fan Company

 CAUTION: 

To avoid possible electrical shock, before installing your fan, 

disconnect the power by turning off the circuit breakers to the outlet box 
and associated wall switch location. If you cannot lock the circuit breakers 
in the off position, securely fasten a prominent warning device, such as a 
tag, to the service panel.

2-1.  Drill two pilot holes into the wood support structure through the 

outermost holes in the outlet box. The pilot holes should be 9/64” 
in diameter.

2-2.  Your fan comes with four neoprene noise isolators (“Isolators”). 

Position the isolators between the ceiling plate and ceiling by 
inserting the raised areas on each isolator into the holes in the 
ceiling plate.

2-3.  Thread the lead wires from the outlet box down through the hole 

in the middle of the ceiling plate.

2-4.  Align the slotted holes in the ceiling plate with the pilot holes you 

drilled in the wood support structure. For proper alignment use 
slotted holes directly across from each other. 

    Note:

 The isolators should be flush against the ceiling.

2-5.  Place a flat washer on each of the two 3” wood screws and pass 

the screws through the slotted holes in the ceiling plate into the 
pilot holes you drilled. 

    Tighten the screws into the 9/64” pilot holes; do not use lubricants 

on the screws. Do not over tighten.

Step 2-2

Flat Washer

3” Wood Screw

Steps 2-3 – 2-5

For Angled Ceilings:

 Be sure to 

orient the ceiling plate so that the 
arrows printed on the ceiling plate are 
pointing toward the ceiling peak. 

Ceiling

 Plate

Isolator

2 • Installing the Ceiling Plate

Summary of Contents for Type 8














Reviews: