Hunter Type 8 Installation And Operation Manual Download

Page: 10 / 13

41968-01 • 04/10/07 • Hunter Fan Company

7 • Installing the Switch Housing

7-1. Connect the upper plug connector from the motor to the lower

plug connector in the switch housing assembly.

Note:

Both plug connectors are polarized and will only fit together

one way. Make sure the connectors are properly aligned before
connecting them. Incorrect connection could cause improper
operation and damage to the product.

7-2. To attach the switch housing, thread the screws through the side

holes of the mounting plate and tighten them securely.

Note:

If you are installing the light fixture, proceed to

8 • Installing the

Light Fixture

. If you are not installing the light fixture, proceed with

steps 7-3 – 7-4 to complete the installation.
7-3. Thread the finial with rod (from the sack parts) through the switch

housing cap and into the switch housing.

7-4. Tighten the finial.

Steps 7-1 – 7-2

Side Holes

Switch

Housing

Switch

Housing

Cap

Finial

Steps 7-3 – 7-4

Summary of Contents for Type 8














Search results

Summary of Contents for Type 8

Reviews:

Related manuals for Type 8

Brands by name

Popular brands

Hunter Type 8, Installation And Operation Manual

Search results

Summary of Contents for Type 8

Reviews:

Related manuals for Type 8

Brands by name

Popular brands