background image

www.huskietools.com

7

IMPORTANT OPERATING PRECAUTIONS 

PRECAUTION FOR THE TOOL

1. Always point the tool 

AWAY

 from other people.

2. If the tool is stored for an extended period at a temperature of less than 25º F (-5ºC), the tool  

 

  should be allowed to return to room temperature to ensure smooth operation Use the tool only  

 

  after it has been at room temperature for 1 hour.

3. Do not drop the tool. 

4. Solvents can be used to clean the head, but should not be used on the plastic body. Use soap and   

  water to clean the body.

1. Do not short circuit the contacts or expose the cartridge to water, oil or solvents.

2. Do not disassemble or attempt to repair the battery cartridge or dispose of in a fire.

3. Do not drop or otherwise abuse the battery cartridge.

4. Do not leave the cartridge in locations where it will be exposed to a temperature greater than 140ºF  

  (60ºC) for an extended period.

5. The battery has a limited life. When the crimping capacity becomes about 1/2 that of the original    

  capacity, the battery should be replaced.

6. If the battery cartridge is stored without being charged, natural drainage will cause the power to be   

  reduced. The battery should be charged every 3 months if not in use.

PRECAUTION FOR THE BATTERY CARTRIDGE

PRECAUTION FOR THE CHARGER 

1.  The LED indicator lights up amber and remains lit when the unit starts charging a battery cartridge.  

  The indicator turns green when charging is completed.

2.  This unit is for charging battery cartridges BP-80, BP-70E, BP-70EI and BP-70MH only. Do not use  

  the charger for any other devices.

3.  Allow battery cartridges to cool before charging. Allow at least 15 minutes between charges when    

  charging several cartridges in succession.

4.  Charge batteries at an ambient temperature of 50º-95ºF (10º-35º C). Charging time is  

 

 

  approximately 50-70 minutes for the BP-80, 50 minutes for the BP-70E and BP-70EI, and 70  

 

  minutes for the BP-70MH.

5.  Never short circuit the output terminals.

6.  Do not expose the charger to water, oil or solvents.

7.  Do not disassemble, attempt to modify, drop or otherwise abuse charger.

Summary of Contents for REC-5OU















Reviews: