background image

All Huskie REC-Series battery driven products carry a 5 year warranty, and the ECO-Series
carry a 3 year warranty. The BP-70E, BP-70EI, and the BP-70MH batteries carry a 5 year 
warranty from the date stamped on the battery. The LED indicator on the BP-70-EI battery
carries a 1 year warranty from purchase date. Hydraulic hammers carry a one year warranty
and all other Huskie products carry a 5 year warranty. Huskie reserves the right to determine
all warranty claims. Failure due to misuse, abuse or repairs attempted by anyone other than
Huskie Tools, Inc., or an authorized service center render this warranty null and void.  Our
patented drop-out bypass cartridge can be re-calibrated or tested at no charge for the life
of the tool.  All factory repaired or reconditioned hydraulic tools carry a one year warranty
on parts and labor.  

REPAIR AND WARRANTY CLAIMS

All claims must be sent to Huskie for inspection and authorization.  A Return Goods
Authorization is required before shipping tools to Huskie. Secure the authorization by 
telephoning 1-800-860-6170 or writing to Huskie's main office with details of claim. Non-
warranty repairs are handled using the same procedure. Repairs exceeding 50% of the cost
of a new tool will be advised before repairs are made.

P

LEASE

R

ETAIN

F

OR

Y

OUR

R

ECORDS

Purchaser’s Name

_____________________________________________________

Address

_____________________________________________________

City, State, Zip

_____________________________________________________

Tool Model Number

_____________________________________________________

Serial Number

_____________________________________________________

Date Purchased From

_____________________________________________________

Purchased From

_____________________________________________________

MODEL SP-40 WARRANTY

Summary of Contents for SP-40













Reviews: