background image

 4

Safety Information (continued)

AIR COMPRESSOR AND  
PNEUMATIC TOOL SAFETY

 

Keep compressors as far from the spraying area as 
possible: at least 15 ft. (4.6 m) from the spraying 
area and all explosive vapors.

 

If connected to a circuit protected by fuses, use time-
delay fuses with this product. 

 

Ensure the hose is free of obstructions or snags. 
Entangled or snarled hoses can cause loss of 
balance or footing, and may become damaged.

 

Use the air compressor only for its intended use. Do 
not alter or modify the unit from the original design 
or function. Never weld or drill holes in the air tank.

 

Never leave a tool unattended with the air hose 
attached. 

 

Do not operate this tool if it does not contain a 
legible warning label.

 

Do not continue to use a tool or hose that leaks air or 
does not function properly.

 

Do not attempt to pull or carry the air compressor 
by the hose.

 

Your tool may require more air consumption than 
this air compressor is capable of providing.

 

Never direct a jet of compressed air toward people 
or animals. 

 

Protect your lungs. Wear a face or dust mask if the 
operation is dusty. 

 

Do not use this air compressor to spray chemicals. 
Your lungs can be damaged by inhaling toxic 
fumes. A respirator may be necessary in dusty 
environments or when spraying paint.

 

This compressor is equipped with a thermal 
overload protector which will shut off the motor if it 
becomes overheated. 

WARNING

:

 Do not attempt to modify this tool or create 

accessories not recommended for use with this tool. 
Any such alteration or modification is misuse and could 
result in a hazardous condition leading to possible serious 
personal injury.

CAUTION

:

 Do not use the compressor in an environment 

that is dusty or otherwise contaminated. Using the air 
compressor in this type of environment may cause damage 
to the unit.

CAUTION

:

 Risk of bursting. Do not adjust the regulator 

to result in output pressure greater than the marked 
maximum pressure of the attachment. Do not use at 
pressure greater than the rated maximum pressure of this 
compressor.

CAUTION

:

 To reduce the risk of electric shock, do not 

expose the compressor to rain. Store indoors. 

C302H_HUSKY_manual_5-15-ENG.indd   4

6/10/15   12:05 PM

Summary of Contents for C302H






























Reviews: