5
HUSKYTOOLS.COM
Contact 1-888-43-HUSKY for further assistance.
Safety Information (continued)
7.
Inspect the tank yearly for rust, pin holes, or other
imperfections that could cause it to become unsafe. Never
weld or drill holes in the air tank.
8.
Make sure the hose is free of obstructions or snags.
Entangled or snarled hoses can cause loss of balance or
footing and may become damaged.
9.
Use the air compressor only for its intended use. Do not
alter or modify the unit from the original design or
function.
10.
Always be aware that misuse and improper handling of
this tool can cause injury to yourself and others.
11.
Never leave a tool unattended with the air hose attached.
12.
Do not operate this tool if it does not contain a legible
warning label.
13.
Do not continue to use a tool or hose that leaks air or does
not function properly.
14.
Always disconnect the air supply and power supply before
making adjustments, servicing a tool, or when a tool is not
in use.
15.
Do not attempt to pull or carry the air compressor by the
hose.
16.
Your tool may require more air consumption than this air
compressor is capable of providing.
17.
Always follow all safety rules recommended by the
manufacturer of your tool, in addition to all safety rules for
the air compressor. Following these rules will reduce the
risk of serious personal injury.
18.
Never direct a jet of compressed air toward people or
animals. Take care not to blow dust and dirt towards
yourself or others. Following this rule will reduce the risk
of serious injury.
19.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
20.
Do not use this air compressor to spray chemicals. Your
lungs can be damaged by inhaling toxic fumes. A
respirator may be necessary in dusty environments or
when spraying paint. Do not carry while painting.
21.
Inspect tool cords and hoses periodically and, if damaged,
have repaired at your nearest Authorized Service Center.
Constantly stay aware of cord location. Following this rule
will reduce the risk of electric shock or fire.
22.
Never use an electrical adaptor with this grounded plug.
23.
Check damaged parts. Before further use of the air
compressor or air tool, a guard or other part that is
damaged should be carefully checked to determine that it
will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorized service center. Following this
rule will reduce the risk of shock, fire or serious injury.
24.
Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. A wire gauge
size (A.W.G.) of at least 14 is recommended for an
extension cord 50 feet or less in length. A cord exceeding
100 feet is not recommended. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier
the cord. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
25.
WARNING: This product contains one or more chemicals
known to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands after
handling.
26.
Save these instructions. Refer to them frequently and use
them to instruct others who may use this air compressor.
If you loan someone this tool, load them these instructions
also.
WARNING:
The operation of any power tool can result in foreign
objects being thrown into your eyes, which can result in
severe eye damage. Before beginning power tool
operation, always wear safety goggles, safety glasses
with side shields, or a full face shield when needed. We
recommend Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply
with ANSI Z87.1.
Summary of Contents for H1504ST2
Page 18: ...18 Service Parts PARTS DIAGRAM...
