background image

 

2

 

Table of Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

California Proposition 65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Work Area Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Personal Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Spraying Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hardware Required  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Package Contents  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Compressor Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Specifi cations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation - Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation - Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Care and Cleaning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Safety Information

This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT 
EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols.

DANGER:

 Indicates an imminently hazardous situation 

which, if not avoided, WILL result in death or serious injury.

WARNING:

 Indicates a potentially hazardous situation 

which, if not avoided, COULD result in death or serious injury.

CAUTION:

 Indicates a potentially hazardous situation which, 

if not avoided, MAY result in minor or moderate injury.

IMPORTANT:

 Indicates important information, that if not 

followed, may cause damage to equipment.

NOTE:

 Information that requires special attention.

CALIFORNIA PROPOSITION 65

WARNING:

 This product or its power cord may contain 

chemicals known to the State of California to cause cancer 
and birth defects or other reproductive harm. Wash hands 
after handling.

WARNING:

 You can create dust when you cut, sand, drill, or 

grind materials such as wood, paint, metal, concrete, cement, 
or other masonry. This dust often contains chemicals known to 
cause cancer, birth defects, or other reproductive harm. Wear 
protective gear.

Summary of Contents for HS518102





























Reviews: