background image

 3 

HUSKYTOOLS.COM

 

 

Please contact 1-888-43-HUSKY for further assistance.

GENERAL SAFETY

DANGER:

 Breathable Air Warning: This compressor/pump 

is NOT equipped and should NOT be used “as is” to supply 
breathing quality air. For any application of air for human 
consumption, you must fi t the air compressor/pump with 
suitable in-line safety and alarm equipment. This additional 
equipment is necessary to properly fi lter and purify the 
air to meet minimal specifi cations for Grade D breathing 
as described in Compressed Gas Association Commodity 
Specifi cation G 7.1, OSHA 29 CFR 1910. 134, and/or Canadian 
Standards Associations (CSA).

Disclaimer of Warranties: In the event the compressor is used 
for the purpose of breathing air application and proper in-line 
safety and alarm equipment is not simultaneously used, 
existing warranties are void, and the Manufacturer disclaims 
any liability whatsoever for any loss, personal injury, or 
damage.

DANGER:

 Never attempt to repair or modify a tank! Welding, 

drilling, or any other modifi cation will weaken the tank, 
resulting in damage from rupture or explosion. Always replace 
worn, cracked, or damaged tanks.

CAUTION:

 See the compressor specifi cation decal for 

maximum operating pressure. Do not operate with pressure 
switch or pilot valves set higher than the maximum operating 
pressure.

IMPORTANT:

 Drain liquid from the tank daily.

NOTE:

 The 

DANGER

WARNING

CAUTION

IMPORTANT

, and 

NOTE

 notifications and instructions in this manual cannot 

cover all possible conditions and situations that may occur. 
It must be understood by the operator that caution is a factor 
which cannot be built into this product, but must be supplied 
by the operator.

1.  Read all manuals included with this product carefully. Be thoroughly familiar with the controls and the proper use of the equipment.

2.  Only persons well acquainted with these rules of safe operation should be allowed to use the compressor.

3.  Tanks rust from moisture build-up, which weakens the tank. Make sure to drain the tank regularly and inspect periodically for unsafe 

conditions, such as rust formation and corrosion.

4.  Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture or depressurizing the 

compressor system.

Safety Information (continued)

Summary of Contents for HS518102





























Reviews: